NATURAL STONE SEALER:

Natural Stone Sealer is a tried and tested weather proof solvent based sealer system, for natural stone and cement tiles. It is very simple to use and is suitable for most types of natural porous tiles. Natural Stone Sealer’s refined non-yellowing resin formula, is designed, for ease of application, protection offered and cost effectiveness. Natural Stone Sealer is both an impregnating and surface sealer so it colour enhances the tile and provides a beautiful sheen finish. Natural Stone Sealer is a breathable sealer. That means it may be applied to areas that have a slight hydrostatic pressure problem. Natural Stone Sealer dries quickly and cures quicker than most other un-accelerated sealers.

Directions:

Always test for desired results in an inconspicuous area before application. This product is flammable. Keep away from open flames and sources of ignition.

  1. Read all instructions and tips before the application so that you can plan the application correctly.
  2. Mask off any adjacent surfaces that need to be protected during the application.
  3. Test for desired results in an inconspicuous area before continuing the application.
  4. Shake or stir well before use
  5. Ensure that surface is clean and free from grout, cement, oil, wax, and other stains. (Clean with the correct Tile & Floor Care product if necessary).
  6. Ensure that the surface and grouting are uniformly dry before application. Wait 24 hours after washing before applying the sealer.
  7. Using a suitable applicator apply an even coat of Natural Stone Sealer to the surface. Do not allow bubbles or pooling.
  8. Allow to dry for 2 hours between coats, and then apply another (thin) coat. In most cases a minimum of 2 coats is necessary.
  9. Apply more coats at 2 hour intervals (if required), until a uniform even sheen is achieved.

Tips:

    1. Do not use applicators that cause bubbles like paint rollers.
    2. Use a lint free cloth or a sheepskin applicator.
    3. Should you have any doubt or queries please phone Tile & Floor Care for advice.
    4. Do not apply while the floor is still damp.
    5. Allow 2-4 days after laying the tile before sealing.
    6. Store and use between temperatures of 5°C – 30°C.
    7. Do not dilute.
Cleaning and sealing of high porosity Slate tiles with Tile & Floor Care Products.
After laying:
During grouting make sure all excess grout is removed from the surface with a damp clean cloth or sponge and fresh clean water. Washing grout and residues off the surface with dirty water and / or cloth or sponge does not clean the surface. Any grout residues will impair the finish after sealing and will result in a very expensive repair. Clean with Tile and Floor Care Grout Off (acidic wash) and Easy Clean (neutralizer) to ensure a residuefree surface.
Choosing a sealer:
When choosing a sealer, one would need to ensure that the sealer you choose will give you the desired finish e.g. matt, satin, gloss or natural with colour enhancement or not. Each sealer gives a different finish to the tile and protects the tile in a different manner. If in doubt phone Tile and Floor Care for free advise on 0800 006173 / 011 822 6901                                                                                                                                                               

TOP SEAL:

Top Seal is a tough and durable surface sealer that protects a tile’s surface from wear and tear and staining. Top Seal may be used on terracotta, slate, sandstone, natural stone, cement, and vinyl tiles. Top Seal is used whenever protection from trafficking is required. Top Seal is easy to apply and will quickly dry to a gloss finish. Top Seal is suitable for interior and exterior application.

Directions:

  1. Read all instructions and tips before the application so that you can plan the application correctly.
  2. Mask off any adjacent surfaces that need to be protected during the application.
  3. Test for desired results in an inconspicuous area before continuing the application.
  4. Ensure that the tile is clean a
  5. nd free from grout, cement, oil, wax and other stains (Clean with the correct Tile & Floor Care product if necessary).
  6. Ensure that the tile is dry enough to accept the sealer (wait approx. 8 hours after cleaning).
  7. Shake or stir well before use.
  8. Using a suitable applicator apply a liberal coat of Top Seal. Do not allow pooling.Wait approx. 4 hours for the coat to dry.
  9. Apply a second coat or a third coat if necessary.

Tips & Tricks:

  1. Do not use paint rollers.
  2. Use a lint free cloth, a sheepskin applicator or a “paint pad” to apply Top Seal.
  3. Do not apply while the floor is still damp.
  4. Do not apply to hot tiles in direct sunlight.
  5. Allow 2 – 4 days after laying the tile before sealing.
  6. Pre-sealing is only recommended for cement tiles.
  7. Do not dilute.
Name Top Seal HP Sealer Natural Stone Sealer
Type Acrylic Urethane Acrylic
Base Water Solvent Solvent
Use Interior & Exterior Interior & Exterior Interior & Exterior
Finish Gloss/Sheen Matt Satin
Colour Enhancement Minimal Colour enhancement Considerable colour change Considerable colour change
Coverage ± 10 – 15m² per 1L ± 7 – 12m² per 1L ± 7 – 12m² per 1L
Maintenance
Interior: Maxi Shine (gloss finish)
Exterior: Easy Seal (sheen finish)
Daily Cleaning: Quick Clean
Daily Cleaning: Quick Clean Daily Cleaning: Quick Clean
Wash & Seal
Same day if tile has
dried sufficiently
48 hours between
washing & sealing
48 hours between
washing & sealing

 

For advise on sealing, phone Tile and Floor Care on 0800 00 6173

Click to download PDF